- Hp Switch 2610-24 Manual
- Hp Procurve 2610 Firmware Download
- Hp Procurve 2610-24 User Manual Guide
- Hp Procurve 2610-24 User Manual Instructions
- Hp Procurve 2610-24-pwr Manual
The HP Procurve managed 24-port switch has 10/100BASE-TX autosensing per port and 2 open transceiver slots for media flexibility. The HP Procurve switch 2524 is ideal for low-cost, managed 10/100 connectivity with uplinks. View and Download HP ProCurve 2610 installation and getting started manual online. ProCurve 2610 Switch pdf manual download. Also for: Procurve 2610 series, Procurve 2610-24, J9085a, Procurve 2610-24/12pwr, J9086a, Procurve 2610-24-pwr, J9087a, Procurve 2610-48, J9088a, Procurve. The ProCurve 2610-24 switch supports twelve trunk groups of up to eight ports each. The ProCurve 2610-48 supports twenty-four trunk groups of up to eight ports each. (Using the Link Aggregation Control Protocol (LACP) option, user can include standby trunked ports in addition to the maximum of four actively trunking ports.). 4-4 Using the Command Line Interface (CLI) Using the CLI Caution ProCurve strongly recommends that you configure a Manager password.If a Manager password is not configured, then the Manager level is not password-protected, and anyone having in-band or out-of-band access to the switch may.
Print|Rate this content |
InformationThis document describes how to configure the port trunking on an HP ProCurve 2610 Switch. DetailsPort trunking allows user to assign physical links to one logical link (trunk) that functions as a single, higher-speed link providing dramatically increased bandwidth. This capability applies to the connections between the backbone devices as well as to the connections in other network areas where the traffic bottlenecks exist. These are the capability of HP ProCurve 2610 Switch regarding the trunking: Port Trunking Support ProCurve Switch ProCurve Switch 2610-24 2610-48 ---------------------- ------------ --------------- Ports per trunk (maximum) 8 8 Trunks per switch (maximum) 12 24 A trunk group is a set of ports configured as the members of the same port trunk. Note that the ports in a trunk group do not have to be consecutive. The Samsung support homepage is your starting point for help with Samsung products, featuring visual guides, manuals, support downloads, tech specs, troubleshooting, and answers. Samsung refrigerator parts diagram. Refrigerators Support helps users troubleshoot common issues. Find answers to service and warranty questions or how to contact Support. Links to software updates, manuals, specifications, and answers are. The switch offers these options for port trunking: The ProCurve 2610-24 switch supports twelve trunk groups of up to eight ports each. The ProCurve 2610-48 supports twenty-four trunk groups of up to eight ports each. (Using the Link Aggregation Control Protocol (LACP) option, user can include standby trunked ports in addition to the maximum of four actively trunking ports.) Configuring a Static Trunk or Static LACP Trunk Group For the 2610-24 switch: Syntax: trunk <port-list> < trk1 .. trk12 > < trunk | lacp > For the 2610-48 switch: Syntax: trunk <port-list> < trk1 .. trk24 > < trunk | lacp > The following example uses ports C4 - C6 to create a non-protocol static trunk group with the group name of Trk2. Removing a port from a trunk can result in a loop and cause a broadcast storm When user remove a port from a trunk where STP is not in use, ProCurve recommends to first disable the port or disconnect the link on that port. Syntax: no trunk < port-list > This example removes ports C4 and C5 from an existing trunk group. ProCurve(config)# no trunk c4-c5 Enabling a Dynamic LACP Trunk Group In the default port configuration, all ports on the switch are set to LACP Passive. However, to enable the switch to automatically form a trunk group that is dynamic on both ends of the link, the ports on one end of a set of links must be LACP Active. The ports on the other end can be either LACP Active or LACP Passive. This command enables the switch to automatically establish a dynamic LACP trunk group when the device ports on the other end of the link are configured for LACP Passive. Syntax: interface < port-list > lacp active This example uses ports C4 and C5 to enable a dynamic LACP trunk group. ProCurve(config)# interface c4-c5 lacp active Removing Ports from a Dynamic LACP Trunk Group To remove a port from dynamic LACP trunk operation, user must turn off LACP on the port. (On a port in an operating, dynamic LACP trunk, you cannot change between LACP Active and LACP Passive without first removing the LACP operation from the port.) Unless STP is running on the network, removing a port from a trunk can result in a loop. To help to prevent a broadcast storm when user remove a port from a trunk where STP is not in use, ProCurve recommends to first disable the port or disconnect the link on that port. Syntax: no interface <port-list> lacp In this example, port C6 belongs to an operating, dynamic LACP trunk. To remove port C6 from the dynamic trunk and return it to passive LACP, do the following: ProCurve>(config)# no interface c6 lacp ProCurve>(config)# interface c6 lacp passive NOTE: In the previous example, if the port on the other end of the link is configured for active LACP or static LACP, the trunked link will be re-established almost immediately. With the following two commands, the port trunking can be checked. Those are very useful during troubleshooting. Listing Static Trunk Type and Group for All Ports or Selected Ports Syntax: show trunks [<port-list>] Listing Static LACP and Dynamic LACP Trunk Data This command lists data for only the LACP-configured ports. Syntax: show lacp For further details, see the HP ProCurve 2610 Management and Configuration Guide. Click here to access the 'HP ProCurve 2610 Management and Configuration Guide'. |
Legal Disclaimer: Products sold prior to the November 1, 2015 separation of Hewlett-Packard Company into Hewlett Packard Enterprise Company and HP Inc. may have older product names and model numbers that differ from current models.
Provide feedback |
Please rate the information on this page to help us improve our content. Thank you! |
- Was the information on this page helpful?
Please wait while we process your request.
Advertising
1-10
Introducing the Switch
Front of the Switch
Front of the Switch
In
tr
o
d
u
c
in
g
th
e
Sw
itc
h
Table 1-4.
Multiple-Display Port LEDs
Reset Button
Hp Switch 2610-24 Manual
This button is for:
■
Resetting the switch
- When the switch is powered on. This action clears
any temporary error conditions that may have occurred and executes the
switch self test.
switch self test.
■
Restoring Factory Default Configuration
- When pressed with the
Clear button in a specific pattern, any configuration changes you may have
made through the switch console, the web browser interface, and SNMP
management are removed, and the factory default configuration is
restored to the switch. For the specific method to restore the factory
default configuration, see
made through the switch console, the web browser interface, and SNMP
management are removed, and the factory default configuration is
restored to the switch. For the specific method to restore the factory
default configuration, see
, “Troubleshooting” of this manual.
Clear Button
This button is used for:
■
Deleting Passwords
- When pressed by itself for at least one second, the
button deletes any switch console access passwords that you may have
configured. Use this feature if you have misplaced the password and need
console access. This button is provided as a convenience, however if you
are concerned with the security of the switch configuration and operation,
you should make sure the switch is installed in a secure location. This
button can be disabled by a CLI command.
configured. Use this feature if you have misplaced the password and need
console access. This button is provided as a convenience, however if you
are concerned with the security of the switch configuration and operation,
you should make sure the switch is installed in a secure location. This
button can be disabled by a CLI command.
■
Restoring Factory Default Configuration
- See Reset Button above.
Switch LEDs
State
Meaning
All 2610 Switches
Port LED View
indicator LEDs
3 green LEDs)
indicator LEDs
3 green LEDs)
Microsoft office outlook 2007 configuration. Then do the setup with Mail from the Control Panel.When I could not get it to work I tried to copy the Exchange location numbers manually, maybe the numbers don't match what they should be? #1 -I am wondering if I should uninstall and reinstall?
Act
FDx
Spd
FDx
Spd
Indicates the Port LEDs are displaying network activity information.
Indicates the Port LEDs are lit for ports that are in full-duplex mode.
Indicates the Port LEDs are displaying the connection speed at which each
port is operating:
• if the Port LED is off, the port is operating at 10 Mbps.
• if the Port LED is flashing, the port is operating at 100 Mbps.
• if the Port LED is on continuously, the port is operating at 1000 Mbps.
Indicates the Port LEDs are lit for ports that are in full-duplex mode.
Indicates the Port LEDs are displaying the connection speed at which each
port is operating:
• if the Port LED is off, the port is operating at 10 Mbps.
• if the Port LED is flashing, the port is operating at 100 Mbps.
• if the Port LED is on continuously, the port is operating at 1000 Mbps.
Switch 2610-PWR Series
LED Mode
indicator LEDs
(PoE is the
additional
LED, green)
indicator LEDs
(PoE is the
additional
LED, green)
PoE
Hp Procurve 2610 Firmware Download
Indicates the Port LEDs are lit for ports that are providing PoE power to the
connected device.
connected device.
Hp Procurve 2610-24 User Manual Guide
Advertising
Hp Procurve 2610-24 User Manual Instructions
Popular Brands
Hp Procurve 2610-24-pwr Manual
Popular manuals